尊龙集团

about_ban

contact_list

    Addr:Xinglong Industrial Zone, Yangzhong City, Jiangsu Province
    Tel: 13852950345
    E-mail:sandy@hansasealant.com

FEP clear straight tube

Publisher:Hansa seal Pubtime:2026-11-11 16:12:00 Close
6af42827c3e70

1. Product Introduction

FEP (Fluorinated Ethylene Propylene) clear straight tube is made of thermoplastic fluoropolymer copolymerized by tetrafluoroethylene (TFE) and hexafluoropropylene (HFP). It features low crystallinity and high transparency, enabling direct visual observation of fluid flow, bubbles and impurities inside the tube.

Main Production Process: Melt extrusion and rapid cooling shaping. Pure FEP resin is melted at 280~340°C, extruded into straight tubes through precision dies, then quickly cooled in a low-temperature water tank to restrain molecular crystallization and guarantee a clear, haze-free tube wall. A high-precision haul-off machine controls wall thickness and outer diameter tolerance to produce rigid straight tubes. They can be cut to custom lengths and are available in two grades: clean grade and general industrial grade.

 

2. Physical & Chemical Properties

 Item  Value  Test Standard
 Density  2.12~2.17 g/cm?  ASTM D792
 Continuous Service Temperature  -80℃ ~ +200℃, short-term peak up to 260℃  —
 Melting Point  265~275℃  —
 Tensile Strength  ≥19 MPa  ASTM D638
 Elongation at Break  ≥250%  ASTM D638
 Shore Hardness  Shore D 55~66  —
 Water Absorption  <0.01%  ASTM D570
 Coefficient of Friction  0.05~0.2 (self-lubricating)  —
 Dielectric Constant @1MHz  ≤2.1  —
 Volume Resistivity  ≥10?? Ω·cm  —
 Dielectric Strength  ≥30 kV/mm  —
 Flammability  UL94 V-0, self-extinguishing  UL94
 Chemical Resistance  Resistant to most strong acids, alkalis, oxidants and organic solvents; only molten alkali metals and elemental fluorine can cause corrosion  —
 Light Transmittance  ≥90% for wall thickness ≤3mm, clear without milky haze  —

   

3. Typical Application Fields

 Industry  Industry  Application Scenarios Selection Requirements
 Semiconductor & Electronics  High-purity chemical delivery, photoresist & etchant piping, ultra-pure water transfer, equipment cooling loops, high-purity gas tubing  High-clean grade, low extractables, particle-free, uniform wall thickness, smooth inner surface
 Biomedicine & Pharma  Process fluid transfer, high-temperature steam sterilization piping, lab reagent tubing  Food/biomedical grade, withstand 121℃ autoclaving, non-toxic leachables
 Chemical Fluid Handling  Strong corrosive acid/alkali delivery, organic solvent transfer, sampling lines, sight level gauge tubes  General corrosion-resistant grade, pressure resistant, anti-aging
 Electrical & Cabling  High-temperature wire insulation sheath, thermowell protection tube, high-voltage insulating sleeve  Excellent insulation, temperature & UV resistance
 New Energy & PV  Wet chemical delivery for photovoltaic process, electrolyte piping, equipment cooling lines  Electrolyte resistance, wide temperature tolerance, low permeability
 Analytical Instruments  Chromatography tubing, micro-fluid delivery, laboratory guide tubes  Small ID, thin wall, high dimensional accuracy, visual fluid monitoring

 

4. Selection & Design Guideline

Selection Principles

4.1 Temperature: Max continuous operating temperature ≤200℃; minimum -80℃. Increase wall thickness for high-temperature & high-pressure service.

4.2 Pressure: Larger wall thickness brings higher pressure rating. Straight tubes normally withstand higher pressure than hoses. Never exceed rated working pressure.

4.3 Purity: General industrial grade for common chemical service; high-purity virgin resin grade for pharma and semiconductor, no regrind material.

4.4 Bending: Minimum bend radius ≥ 6 × outer diameter. Sharp folding and flattening are forbidden to avoid cracking.

Standard Metric Sizes (ID × OD, unit: mm)

 Spec ID×OD  ID Tolerance  Wall Thickness  OD Tolerance  Recommended Application
 2×3  ±0.10  0.5  ±0.10  Micro-fluid, instrument tubing
 3×4  ±0.15  0.5  ±0.15  Small-flow laboratory tubing
 4×6  ±0.15  1.0  ±0.20  General chemical & pneumatic lines
 6×8  ±0.20  1.0  ±0.20  Chemical transfer, sight level tubes
 8×10  ±0.20  1.0  ±0.20  Medium-flow corrosion-resistant piping
 10×12  ±0.20  1.0  ±0.20  Semiconductor high-purity fluid lines
 12×14  ±0.30  1.0  ±0.20  Large-flow chemical transfer

Custom service: ID range 0.5~200 mm, wall thickness 0.12~3 mm. Imperial sizes (1/8", 1/4", 3/8", 1/2") available upon request.

Pressure Reference

? Ambient temperature (23℃): Thin wall (0.5mm) max pressure ≤0.6 MPa; 1.0mm wall max pressure ≤1.2 MPa

? At 150℃: Pressure rating drops to 50% of room-temperature value; at 200℃, rating reduces further, pressure must be lowered accordingly.

 

5. Operation & Maintenance

5.1 Installation Notes

5.1.1 Cutting: Use dedicated plastic tube cutter for clean, burr-free cuts to prevent end cracking. Hot cutting is prohibited.

5.1.2 Bending: Follow minimum bend radius ≥ 6 × OD. Avoid sharp bends and dead folds. Install spring guards for vibration-prone sections.

5.1.3 Connection: Use FEP compression fittings or flared fittings. Do not force-fit to avoid stress cracking at tube ends.

5.1.4 Mounting: Secure tube clamps with moderate tension; avoid permanent compression creep and deformation.

5.2 Routine Maintenance

5.2.1 Visual inspection regularly: Check for whitening, cracks, bulges or creep deformation. Haze/whitening on clear wall indicates crystallization aging; replace the tube immediately.

5.2.2 Media control: Keep away from molten alkali metal and elemental fluorine. Limit temperature and pressure when transferring strong oxidants.

5.2.3 Cleaning: Flush clean-grade tubing only with DI water; do not soak in organic solvents. Autoclave temperature controlled at 121℃; repeated sterilization cycles are recommended under 200 times.

5.2.4 Storage: Store indoors away from UV light, ozone and heat sources. Outdoor long-term exposure will accelerate yellowing and aging.

Troubleshooting

? Tube wall turns white and loses transparency: Caused by over-temperature crystallization. Replacement required.

? Leakage at fitting: Mostly stress crack at tube end. Re-cut flat and reassemble.

? Bulging under continuous pressure: Under-sized wall thickness; switch to heavier wall specification.

 

6. Development Trends

6.1 Higher Purity: Driven by semiconductor and biopharma industries, electronic-grade FEP straight tubes are rapidly upgraded. Metal impurities are controlled down to ppb level with low particle generation and ultra-low extractables to meet 12-inch wafer and high-end bioprocess requirements. High-purity products become the main growth segment.

6.2 Miniaturization & Ultra-precision: Demand rises sharply for micro-ID, thin-wall FEP tubes for microfluidics, minimally invasive medical devices and precision analytical instruments, with tolerance controlled within ±0.05 mm.

6.3 Intelligent Production: Extrusion lines adopt automatic constant-tension haul-off and online crystallinity monitoring to reduce batch deviation. Laser welding gradually replaces traditional compression joints for superior system tightness.

6.4 Accelerated Domestic Substitution: Domestic high-purity FEP resin gradually replaces imported feedstock and cuts cost of premium tubing. Local manufacturers obtain certifications from semiconductor and pharma tier-1 customers, breaking overseas brand dominance.

6.5 Multi-functional Composite Products: Sensor-integrated FEP tubes are emerging, with built-in temperature and deformation monitoring layers for real-time pipeline health monitoring in high-end fluid systems.

 

7. Market Expansion Opportunities

7.1 Semiconductor Wafer Fabrication (Core Growth Market)

Conventional chemical piping is upgraded to ultra-clean FEP straight tubes for photoresist, etchant and UPW transfer. Driven by continuous capacity expansion of domestic 12-inch fabs, high-purity FEP tubing enjoys double-digit growth and represents the largest future application track.

7.2 High-end Medical Consumables (High-margin Segment)

New applications include endoscope sleeves, interventional catheters, extracorporeal circulation tubing and gene therapy fluid lines. Benefiting from biocompatibility, autoclavability and visual clarity, medical-grade FEP tubing is gradually replacing imported catheters with attractive premium pricing.

7.3 New Energy as Fresh Growth Driver

Lithium battery electrolyte transfer, PV wet chemical piping and energy storage liquid cooling circuits. FEP’s excellent electrolyte resistance, low permeation and wide temperature range make it ideal for new-energy fluid systems.

7.4 Aerospace & Defense Supporting

Transparent monitoring lines for aviation hydraulic oil and fuel, instrument fluid tubing for airborne equipment. Military-grade FEP tubes withstand extreme temperature, oil and weather aging, supported by serial production of domestic large aircraft.

7.5 Retrofit of Traditional Chemical Plants

Replacement for glass, PVC and PP sight gauge tubes. FEP clear tubes are shatterproof, corrosion resistant and 3~5 times longer service life than glass. Retrofit demand for level gauges and sampling lines in chemical plants remains steady.

 

8. Summary & Closing Remarks

FEP clear straight tube combines four core strengths: high transparency, universal corrosion resistance of perfluoropolymers, wide thermal stability and outstanding electrical insulation. It is the only fluoropolymer straight tube maintaining permanent clarity, filling the gap of opaque PTFE and haze-prone PFA.

The industry is shifting from commodity industrial tubing toward ultra-clean, precision micro and smart composite grades. Semiconductor, biopharma and new energy sectors will keep expanding market volume. With localization of raw materials and extrusion technology, domestic FEP clear tubing is catching up with imported alternatives in purity, precision and consistency while offering better cost performance.

Future product development will focus on ultra-low extractables, thin-wall high precision and intelligent online monitoring, continuously penetrating high-end equipment, precision medical and integrated circuit markets with promising long-term potential.

Product
PTFE PRODUCTS
NYLON PRODUCTS
PEEK PRODUCTS
PE PRODUCTS
POM PRODUCTS
OTHER PLASTIC PRODUCTS
SEALING ELEMENT
PVC
About Us
Company profile
corporate culture
Enterprise honor
News Center
Company news
Industry news
Contact Us
Addr:Xinglong Industrial Zone, Yangzhong City, Jiangsu Province
Tel:13852950345
Email:sandy@hansasealant.com
erweima
【网站地图】